Contact Me

Hi,

My name is Ben Rothschild

I am a 4th year Mechanical Engineering student who loves to build robots while learning how to use new electrical and mechanical components.

Email me anytime at benrothschild [at] builtbyben [dot] net

Outside of engineering I ride with Georgia Tech Cycling and Snyder Factory Racing

24 thoughts on “Contact Me”

HEY ben , ive been interested in your work , and i was wondering what software you used to make the chipper boards.

Reply ↓

Ben on April 9, 2013 at 8:28 pm said:

The PCB was made with CadSoft Eagle. The chips are programmed with the Arduino IDE.
http://www.cadsoftusa.com/

Reply ↓
- Jordan on June 14, 2013 at 1:16 pm said:
  
  Thanks
  
  Reply ↓
  - Jordan on June 14, 2013 at 1:20 pm said:
    
    was your kickstarter a success ?
    
    Reply ↓
    - Ben on June 16, 2013 at 2:19 pm said:
      
      So far it has been going according to plan!

Hello, Ben. Tell me, please, will your board works on Arduino Leonardo?

Reply ↓

Ben on May 6, 2013 at 8:31 am said:

It will not work if you place the shield on the Leonardo. What you have to do is connect the 6 pin header on the Chipper to the 6 pin header on the Leonardo. Then it will work with the ArduinoISP sketch.

Reply ↓
- Dmitriy on May 7, 2013 at 1:03 am said:
  
  Thanks a lot!
  
  Reply ↓

I want of these boards…how can i get one

Reply ↓

Ben on July 14, 2013 at 6:12 pm said:

Please email me at benrothschild@builtbyben.net and you can order a board and ATtiny chips.

Reply ↓

Is it possible to get the schematics in pdf format?

Reply ↓

Ben on July 29, 2013 at 8:10 pm said:

Yes. Please check the Chipper Circuit Board files on GitHub.

Reply ↓
- warm38@juno.com on July 30, 2013 at 7:59 am said:
  
  Uhhh… I looked on the site for the link to it, but couldn’t find the link to gethub. Could you point it out to me real clear like, ‘cuz I aint one for tact — I need it right out in the open to find stuff.
  
  Reply ↓
  - Ben on July 30, 2013 at 11:58 am said:
    
    Please see:
    https://github.com/BuiltByBen/Chipper-Circuit-Board
    
    Reply ↓
    - wade smith on July 30, 2013 at 12:07 pm said:
      
      Thanks. I actually found it (with your help). 🙂

Hello Ben, I am one of the International backers. Any date for us?. Only to know when our envy will stop

Reply ↓

Ben on August 7, 2013 at 7:23 pm said:

It was mailed out today. It should arrive within 3 weeks.

Reply ↓
- Hector Segura on August 7, 2013 at 7:40 pm said:
  
  Thank you again for the FAST reply. So … to wait mail …;)
  
  Reply ↓

Hi Ben, I also paid you through paypal, but have not heard back from you. Can you update on the shipment please.

Reply ↓

Ben on August 7, 2013 at 7:22 pm said:

It was mailed out today. It should arrive within 3 weeks.

Reply ↓
- Sanjay on August 7, 2013 at 7:46 pm said:
  
  Ok…
  
  Reply ↓

Hello, Ben. Do you have any tutorials on how to test input and output on the analog channel, with the Chipper? I inherited one from a friend and have not electronics experience, but have lots of code experience.

Reply ↓